Ch. 3
Нам обязательно поможет в изучении Powershell
Listing тут
Нам обязательно поможет в изучении Powershell
Listing тут
Jerry Lee Ford - Microsoft Windows PowerShell 2.0 Programming for the Absolute Beginner (2nd Ed) 2008
Книга посвящена Ver2, Ver 3 Powershell'а
Pipeline
cmd.exe, данные передаются как текст => затруднения, когда ожидаемяй формат отличается от необходимого.
Windows PowerShell возвращает объекты, к свойствам или методом обращается второй командлет.
"With object piping, the programmer is relieved of the responsibility of formatting object data, significantly simplifying the scripting process." - стр. 9
Listing тут
Pipeline
cmd.exe, данные передаются как текст => затруднения, когда ожидаемяй формат отличается от необходимого.
Windows PowerShell возвращает объекты, к свойствам или методом обращается второй командлет.
"With object piping, the programmer is relieved of the responsibility of formatting object data, significantly simplifying the scripting process." - стр. 9
Listing тут
[Специалист] Автоматизация административных задач при помощи Windows PowerShell 3.0 [2015, RUS]
Видео 1-3
И то, что удалось извлечь
И то, что удалось извлечь
Richard Siddaway - PowerShell in Practice - 2010
Просмотрел 1-е 4 главы.
Нет заданий в конце каждой главы. Рассматривает PS ver.2, ver.3
Форум тут. Из книги запустил скрипты:
Взаимодействие с WMI
Время последней перезагрузки
Get-WMIObject -Class Win32_OperatingSystem -property LastBootUpTime | foreach {[System.Management.ManagementDateTimeConverter]::ToDateTime($_.LastBootUpTime)}
ИД процесса приложения notepad.exe
Get-WmiObject -Class Win32_Process -Filter 'Name = "notepad.exe"' | Select Name, Processid | Format-Table -AutoSize
Нет заданий в конце каждой главы. Рассматривает PS ver.2, ver.3
Форум тут. Из книги запустил скрипты:
Взаимодействие с WMI
Время последней перезагрузки
Get-WMIObject -Class Win32_OperatingSystem -property LastBootUpTime | foreach {[System.Management.ManagementDateTimeConverter]::ToDateTime($_.LastBootUpTime)}
ИД процесса приложения notepad.exe
Get-WmiObject -Class Win32_Process -Filter 'Name = "notepad.exe"' | Select Name, Processid | Format-Table -AutoSize
try to connect two modules: WIC-1T and WIC-2T by this cables: DB60-V35MT + V35(female)-RS232(male) + SS-RS232FC. All cables standard length, about 3 meters. This means that summary length of all cables about 6 meters. I configure this modules on 2651XM, IOS 12.3.Lights on both modules green, but "Serial1/0 is up, line protocol is down "
Hello, friends.
I try to connect two modules: WIC-1T and WIC-2T by this cables: DB60-V35MT + V35(female)-RS232(male) + SS-RS232FC. All cables standard length, about 3 meters. This means that summary length of all cables about 6 meters. I configure this modules on 2651XM, IOS 12.3.Lights on both modules green, but "Serial1/0 is up, line protocol is down "
DB60-V35MT + V35(female)-RS232(male) - are from the right side of the photo.
Wic-1T configuration (DTE)
interface Serial1/0
ip address 10.0.0.2 255.255.255.0
encapsulation ppp
Wic-2T configuration (DCE)
interface Serial0/1
ip address 10.0.0.1 255.255.255.0
encapsulation ppp
clockrate 2000000
dce-terminal-timing-enable
Serial1/0 is up, line protocol is down
Hardware is DSCC4 Serial
Internet address is 10.0.0.2/24
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, loopback not set
Keepalive set (10 sec)
LCP Listen
Closed: IPCP, CDPCP
Last input never, output 00:02:51, output hang never
Last clearing of "show interface" counters 00:03:56
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 1158 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
11 packets output, 154 bytes, 0 underruns
0 output errors, 0 collisions, 4 interface resets
0 output buffer failures, 0 output buffers swapped out
29 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
Serial0/1 is up, line protocol is down
Hardware is PowerQUICC Serial
Internet address is 10.0.0.1/24
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, LCP REQsent, loopback not set
Keepalive set (10 sec)
Last input never, output 00:00:00, output hang never
Last clearing of "show interface" counters 00:04:15
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 1158 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
52 packets output, 728 bytes, 0 underruns
0 output errors, 0 collisions, 16 interface resets
0 output buffer failures, 0 output buffers swapped out
10 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
I try to connect two modules: WIC-1T and WIC-2T by this cables: DB60-V35MT + V35(female)-RS232(male) + SS-RS232FC. All cables standard length, about 3 meters. This means that summary length of all cables about 6 meters. I configure this modules on 2651XM, IOS 12.3.Lights on both modules green, but "Serial1/0 is up, line protocol is down "
DB60-V35MT + V35(female)-RS232(male) - are from the right side of the photo.
Wic-1T configuration (DTE)
interface Serial1/0
ip address 10.0.0.2 255.255.255.0
encapsulation ppp
Wic-2T configuration (DCE)
interface Serial0/1
ip address 10.0.0.1 255.255.255.0
encapsulation ppp
clockrate 2000000
dce-terminal-timing-enable
Serial1/0 is up, line protocol is down
Hardware is DSCC4 Serial
Internet address is 10.0.0.2/24
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, loopback not set
Keepalive set (10 sec)
LCP Listen
Closed: IPCP, CDPCP
Last input never, output 00:02:51, output hang never
Last clearing of "show interface" counters 00:03:56
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 1158 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
11 packets output, 154 bytes, 0 underruns
0 output errors, 0 collisions, 4 interface resets
0 output buffer failures, 0 output buffers swapped out
29 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
Serial0/1 is up, line protocol is down
Hardware is PowerQUICC Serial
Internet address is 10.0.0.1/24
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, LCP REQsent, loopback not set
Keepalive set (10 sec)
Last input never, output 00:00:00, output hang never
Last clearing of "show interface" counters 00:04:15
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 1158 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
52 packets output, 728 bytes, 0 underruns
0 output errors, 0 collisions, 16 interface resets
0 output buffer failures, 0 output buffers swapped out
10 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
Lubuntu внутри домашней сети
Не мог установить, пока не поменял адресное пространство. Мой Netgear напрочь отказывался пропускать вовне сеть 169.254.0.X / 24
После сброса в дефолтный конфиг - пинги пошли и настала пора конфига SAMBA
https://ubuntuforums.org/showthread.php?t=1623346
To enable file sharing on a Lubuntu 10.10 machine, go to Preferences > Synaptic Package Manager and add the following:-
* samba
* system-config-samba
* gvfs-bin
* gvfs-backends
После всего ярлык SAMBA не хотел запускаться
После сброса в дефолтный конфиг - пинги пошли и настала пора конфига SAMBA
https://ubuntuforums.org/showthread.php?t=1623346
To enable file sharing on a Lubuntu 10.10 machine, go to Preferences > Synaptic Package Manager and add the following:-
* samba
* system-config-samba
* gvfs-bin
* gvfs-backends
После всего ярлык SAMBA не хотел запускаться
- при запуске через ком. строку не находилсярешено:Установил
SystemError: could not open configuration file `/etc/libuser.conf': No such file or directory решено:sudo touch /etc/libuser.conf
Настройка SAMBA Если SAMBA не хочет запускаться, после смены места монтирования папок, то проще её переустановить:sudo apt-get purge samba-common
sudo apt-get autoremove
sudo apt-get update
sudo apt-get install samba smbclient проверкаsmbclient -L 127.0.0.1 -N
Не знаю, почему так получилось.. прописал ip-адрес и имя сервера в
windows\system32\drivers\etc\hosts и монтировал по имени, а не по
адресу:
net use m: \\alexlaptop\ktorrent Настройка SSH:
This service will start running as soon as it is installed. To verify this, you can do
- sudo apt-get install openssh-server
- ssh localhost
yes to the question about the unknown fingerprint and do you want to continue connect, and then providing your password. You will then log in to your own local computer over SSH. This is pretty useless, except as a test, so type
- exit
to end that SSH session. Качаем и ставим Teamviewer:sudo dpkg -i teamviewer_linux_x64.deb
1. лечим отсутствие зависимостей:sudo apt-get -f install
2. доставляемDependency is not satisfiable: libpng12-0
3. еще раз ставимsudo dpkg -i teamviewer_linux_x64.deb
сессия в кармане. ))) Запуск Utserver из командной строки utserver -settingspath /opt/utorrent-server-alpha-v3_3/ & Установка HAMACHI для доступа извне: https://help.ubuntu.com/community/Hamachi http://ubuntovod.ru/instructions/hamachi-ubuntu-linux.htmlСтавим на Lubuntu и на Win клиента. Из-под Ubunta создаем сеть. Клиентом цепляемся к ней, получаем SSH сессию Теперь чтобы подключиться защищенным пользователем без прав, надо:1. Создать пользователя,Задать ему каталог, описание, shell, имя
sudo useradd -m -d /home/user2 -c "user for R2" -s /bin/bash user2 2. Задать скрипт для запуска .bash_profile со стартом telnet сессии на нужный порт:#!/usr/bin/expect -f
set timeout 20
set IPaddress 192.168.1.253telnet $IPaddress XXXX
exit3. сменить у скрипта группу chgrp и владельца chown на соответствующего пользователя4. задать пароль пользователю passwd Список команд mc (http://mydebianblog.blogspot.ru/2011/01/midnight-commander.html) Распечатать: https://cloud.github.com/downloads/drakulavich/russian-mc-cheatsheet/rmc.pdf
Подписаться на:
Сообщения (Atom)